Home 
Delivery 48h 
Secure payments 
Technical & commercial support
RD-Monofloor PU
Technical sheetFast drying floor paint for workshops, technical rooms and balconies.
• Based on acrylic and polyurethane resins, UV resistant.
• Protects floors against wear and abrasion.
• Virtually odorless, can be used in occupied buildings without disturbing.
RD-Monofloor PU is an easy-to-apply floor coating system suitable for protecting a wide variety of floors, including those in warehouses with moderate traffic.
RD-Monofloor PU dries quickly and significantly reduces downtime. Therefore, it can be specified when it’s required to have the spaces available quickly.
Calculate here the amount of paint needed for your project
Technical sheet
Description of the product
USE:
Fast drying floor paint for workshops, technical rooms and balconies.
FEATURES:
Single component floor coating based on acrylic and polyurethane resins for the protection of floors against wear and abrasion.
RD-Monofloor PU is water-based, easy to handle, safe and has no fire risks.
It is a fast-drying coating system that greatly reduces downtime during installation.
Virtually odour free, it does not affect neighbouring occupants and can therefore be used in occupied buildings.
RD-Monofloor PU is UV resistant and can therefore be applied outdoor like on balconies.
It has a very good resistance against wear and abrasion, however, in the event of a more intensive use of the floor by forklifts and trucks, we recommend the use of RD-Hydropox or RD-Hydrograff HP floor coating system.
RD-Monofloor PU is part of the SCS – Single Coating System - product group.
SUBSTRATES:
Concrete – previously painted floors
Systems
On porous floors: | Wet film thickness in microns / mils | Dry film thickness in microns / mils | Consumption per m² / ft² per gallon | Comments | |
Primer | RD-Monofloor PU | 200 / 8 | 85 / 3,4 | 0,20 L / 200 | Dilute the first coat by 10% with water |
Finish | RD-Monofloor PU | 200 / 8 | 85 / 3,4 | 0,20 L / 200 | |
TOTAL | 170 / 6,8 | 0,40 L / 100 | |||
On non-porous floors: | Wet film thickness in microns / mils | Dry film thickness in microns / mils | Consumption per m² / ft² per gallon | |
Primer | RD-Monofloor PU | 200 / 8 | 85 / 3,4 | 0,20 L / 200 |
Finish | RD-Monofloor PU | 200 / 8 | 85 / 3,4 | 0,20 L / 200 |
TOTAL | 170 / 6,8 | 0,40 L / 100 | ||
On balconies on top of RD-Elastodeck waterproofing systems: | Wet film thickness in microns / mils | Dry film thickness in microns / mils | Consumption per m² / ft² per gallon | |
Finish | RD-Monofloor PU | 200 / 8 | 85 / 3,4 | 0,20 L / 200 |
On metal staircases or platforms (including galvanized, stainless steel and aluminium):
Apply a first coat of RD-Monoguard SG followed by two layers of RD-Monofloor PU.
On ceramic floors, tiles:
Apply a first coat of RD-Multiprim followed by two layers of RD-Monofloor PU.
Risks of chemical spills:
The system can be top coated by one or two coats of RD-Hydrograff HP.
Aesthetical fresh-up:
A single coat is possible on previously painted surfaces in need of an aesthetic refreshment.
Anti-skid system:
1/ Broadcast sand or quartz (silicic sand 99% purity 0,3-1mm) on the freshly painted first coat of RD-Monofloor PU. Broadcast until rejection or lightly depending on the required roughness.
2/ Wait at least two hours until the coating is dry.
3/ Brush off the non-adhering sand.
4/ Apply the second coat of RD-Monofloor PU.
Application instructions
APPLICATION CONDITIONS:
Ambient temperature: minimum 5° C (41°F) – Optimal between 12° and 25°C (54° and 77°F).
Relative humidity: maximum 80 %
Dew point > 3°C (5°F)
The concrete screed may not contain more than 5% of humidity.
APPLICATION MEANS:
Brush, roller or airless (nozzle size: 015–021)
PREPARATION OF THE SUBSTRATE:
Concrete floors:
The substrate must be clean: dry, degreased and dust free. Non adhering elements such as older coatings must be removed.
Cracks and damages can be repaired using RD-Acryl W and RD-Cement Filler/Mix.
In case of new polished concrete floors, the curing compound should be removed first by means of a curing remover (30% solution of hydrogen chloride) or mechanically.
In general, and certainly in case of a smooth surface, using a diamond sanding machine to prepare the surface will allow to increase the mechanical adhesion of the coating and its lifespan.
DILUTION:
Product is ready-for-use. Dilute with maximum 3% water when applying by airless or in warm weather conditions (> 25°C / > 77°F).
DRYING TIME (20°C - 68°F):
Touch dry: +/- 2 hours
Recoatable: +/- 4 hours
CLEANING OF TOOLS:
Water
SPECIFICITIES:
Mix well before use.
Technical data
FINISH (Gardner 60°):
Satin +/- 30 % +/- 5
COLOURS:
Stock colours: White, Traffic Grey A RAL 7042, Signal Grey RAL 7004
RAL, NCS and bespoke colours.
Available on RD Coatings dispensing system.
DENSITY:
1.2 +/- 0.05 g/cm³
SOLIDS CONTENT:
In weight: 47 % +/-2
In volume: 37 % +/-2
VISCOSITY:
50 - 70 P (Brookfield 20RPM)
VOC CONTENT:
< 40 g/L
FLASH POINT:
Not flammable
STORAGE:
24 months, keep away from frost and store away from heat.
Safety data
Information related to hygiene and to safety can be found in the Safety Data Sheet available on request.
These specifications are given for information. Since the manufacturer is not able to check the application of the products, he cannot accept any responsibility for it. This technical data sheet replaces all previous editions.
VERS. F012/230221
Fast drying floor paint for workshops, technical rooms and balconies.