
Corporate
- Français
- Nederlands
- English
Shop Belgium
Ireland
Netherlands
- MenuBack
-
Home
- Solutions
Anticorrosion, metal structures and objects
Anticorrosion, metal structures and objectsConcrete, walls and exterior facades
Concrete, walls and exterior facadesRoofs & Waterproofing
Roofs & WaterproofingBalconies and outdoor floors
Balconies and outdoor floorsFloors: garages, warehouses, technical rooms, parkings
Floors: garages, warehouses, technical rooms, parkings
- Products
- References
- RD Coatings Academy
- Our company
Our company
- News
- Contact
Technical & commercial support
RD-AquaRoad
Technical sheetWaterbased, one component, unbeaded traffic paint of the A2 type, based on pure acrylic resin and titanium dioxide.
Calculate here the amount of paint needed for your project
Technical sheet
Description of the product
USE:
Fast drying A2 type traffic paint for road markings, especially suited for outdoor lines and crosswalks in populated or rural areas
FEATURES:
Single component water-based traffic paint based on pure acrylic resins for outdoor use only.
RD-Aquaroad is water-based, easy to handle, safe and has no fire risks.
It is a fast-drying coating system that greatly reduces downtime during installation.
Virtually odour free, it does not affect neighbouring occupants and can therefore be used in densely populated or rural areas.
RD-Aquaroad is UV resistant and has very good resistance against wear and abrasion.
RD-Aquaroad is part of the SCS – Single Coating System - product group.
SUBSTRATES:
Concrete – asphalt
Systems
On new asphalt | Wet film thickness in microns / mils | Dry film thickness in microns / mils | Consumption per m² / ft² per gallon | |
Primer | RD-Aquaroad | 100 / 4 | 60 / 2,5 | 0,15 Kg / 400 |
Finish | RD-Aquaroad | 400 / 16 | 240 / 10 | 0,6 Kg / 100 |
TOTAL | 300 / 12,5 | 0,6 Kg / 100 |
Beads:
It is possible to apply beads in the paint at a rate of 300 g/m²
Sandwich system:
Apply 300 g/m² of Aquaroad and sprinkle the beads gradually at a coverage of 300 g/m². Then apply again 300 g/m² of Aquaroad.
Multilayer system:
Apply 300 g/m² of Aquaroad and sprinkle the beads gradually at coverage of 300 g/m². Then apply again 300 g/m² of Aquaroad and sprinkle again the beads at coverage of 300 g/m².
Aesthetical fresh-up:
A single coat is possible on previously painted surfaces in need of an aesthetic refreshment.
Application instructions
APPLICATION CONDITIONS:
Ambient temperature: minimum 10° C (50°F)
Optimal between 12° and 25°C (54° and 77°F).
Relative humidity: maximum 85 %
APPLICATION MEANS:
Brush or airless (nozzle size: 019–025)
PREPARATION OF THE SUBSTRATE:
The substrate must be clean: dry, degreased and dust free. Non adhering elements such as older coatings must be removed.
DILUTION:
Product is ready-for-use.
DRYING TIME (20°C - 68°F):
Touch dry: +/- 30 minutes
CLEANING OF TOOLS:
Water
SPECIFICITIES:
Mix well before use.
Technical data
FINISH (Gardner 60°):
Mat 5 % +/- 5
COLOURS:
White, Yellow, Black, Red, Orange, Green, Blue
DENSITY:
1.55 +/- 0.05 g/cm³
SOLIDS CONTENT:
In weight: 75 % +/-2 (white)
In volume: 61 % +/-2 (white)
VISCOSITY:
90 KU (Krebs)
VOC CONTENT:
< 55 g/L
FLASH POINT:
Not flammable
STORAGE:
24 months, keep away from frost and store away from heat.
Norms et tests
![]() | ISO 16000-6 / VOC Classification in France |
Safety data
Information related to hygiene and to safety can be found in the Safety Data Sheet available on request.
These specifications are given for information. Since the manufacturer is not able to check the application of the products, he cannot accept any responsibility for it. This technical data sheet replaces all previous editions.
VERS. F005/230222

Waterbased, one component, unbeaded traffic paint of the A2 type, based on pure acrylic resin and titanium dioxide.